AkerSolutions, Fornebu, Norway
In COMSOL Multiphysics it is possible to implement and simulate several independent models in parallel. This can be meaningful when the different models are coupled to each other by some kind of interaction. If a part of the geometries is identical in all models, this part can be reduced in that it is implemented in only one of the geometries. In the other geometries only its solution towards ...
I.T. Bodey, R.V. Arimilli, and J.D. Freels 
The University of Tennessee, Knoxville, TN, USA,
Oak Ridge National Laboratory, Oak Ridge, TN, USA
Modernization of the High Flux Isotope Reactor (HFIR) thermal-hydraulic (TH) design and safety analysis capability is an important step in preparation for the conversion of the HFIR core from a high enriched Uranium (HEU) fuel to a low enriched Uranium (LEU) fuel. Currently, an important part of the HFIR TH analysis is based on the legacy Steady State Heat Transfer Code (SSHTC). The SSHTC is a ...
Ford Motor Company
Dr. Bernardi is a Research Engineer with Ford Motor Company in Dearborn, MI. Her research focuses on the analysis and simulation of electrochemical energy-storage and conversion systems. In particular, Dr. Bernardi develops mathematical models that predict system behavior and identify governing physicochemical processes. Experimental investigations support model development, analysis, and ...
G. Selembo, P. Selembo, J. Stanton, and G. Paulsen
University of North Carolina
Surface aeration systems are used in the wastewater treatment industry for the transfer of oxygen in the activated sludge process. These systems are capital intensive and also require a significant amount of energy to operate. Scale-up and design of these systems is largely empirical, and due to the size of these systems, modifications for experimental testing can be economically prohibitive. ...
A. Sun, and S. Murray
Dept. of Biomedical Engineering
UCLA, Los Angeles, CA
Implantable Collagen sponges are used in Spinal Surgery as Drug Delivery Scaffolds. An optimal concentration of growth factor that strikes a balance between bone growth and adverse diffusion effects is difficult to find. The porous sponge also serves as a scaffold for Osteoblast growth, and fluid shear has been shown to mediate biological effects on that cell type. We use COMSOL Multiphysics ...
Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method
M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic properties of CNT based polymer composites are evaluated using a square Representative Volume Element (RVE) in ...
J. Anza, and M. Esteves
Department of applied mathematics, University of the Basque Country, Bilbao, Spain
University of the Basque Country, Bilbao, Spain
This work deals with the computer simulation of the blood flow, the arterial wall deformation and their 3D bidirectional interaction, including initial stresses and root displacements. The flow is laminar and steady with flexible walls modeled with a hyperelastic Demiray material model. Poiseuille formula is used to check the bidirectional interaction. 2D axisymmetric and full 3D models have ...
R. Coker, J. Mansell
NASA - Marshall Space Flight Center, Huntsville, AL, USA
We have started constructing preliminary design COMSOL models of a bacteriologically driven \'fuel cell\' that is intended to process waste products, such as carbon dioxide and brine, from a crewed vehicle. At this early stage, this complex system is reduced to two electrodes separated by a membrane. The electrolyte is a brine appropriate for growing methanogenic bateria, though none are ...
G.E. Stebner, C. Hartwig
Ostfalia University, IMEC, Wolfenbüttel, Germany
In this paper an EMVD (Electro-Mechanical Valve Drive) for combustion engines is redesigned to achieve a fail-safe behavior when power loss occurs. The AC/DC Module and the Moving Mesh interface of COMSOL Multiphysics 4.2 are used to build up a transient model. This model also includes the calculation of eddy currents.
S. Takahashi, S. Ogata
Tokyo Metropolitan University Hachioji City, Tokyo, Japan
We studied the influence of a number of gas-liquid interface on the drag reduction effect by numeric simulation. Level set method was used for an analysis of gas-liquid interface. The analytic model is rectangular channel of height h = 5 micrometer and width w = 20 micrometer with two hydrophobic microstructures in bottom of channel. In this channel, we found that the liquid penetrates in the ...