Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
C. Siegel[1,2], G. Bandlamudi[1,2], and A. Heinzel[1,2]
Zentrum für BrennstoffzellenTechnik (ZBT) gGmbH, Duisburg, Germany
Institut für Energie- und Umweltverfahrenstechnik, University of Duisburg-Essen, Duisburg, Germany
Phosphoric acid doped polybenzimidazole (PBI) membranes are commonly used in today’s high-temperature polymer-electrolyte-membrane (HTPEM) fuel cell technology. COMSOL Multiphysics is used to model and simulate the three-dimensional, single-phase, non-isothermal overall cell behaviour at different operating points. The sol-gel PBI/H3PO4 membrane behaviour is modeled using an Arrhenius ...
C. Gavrila, A. Ghiaus, and I. Gruia
Technical University of Civil Engineering Bucharest, Faculty of Building Services, Bucharest, Romania
University of Bucharest, Faculty of Physics, Bucharest, Romania
A dynamic mathematical model, based on physical and transport properties and mass and energy balances, was developed for the simulation of unsteady convective drying of agricultural products (fruits and vegetables) in static bed conditions. The model utilizes water sorption isotherm equations and the change in solid density due to the shrinkage phenomenon. The aim of this article is to describe ...
M. Darif, and N. Semmar
GREMI-UMR6606, CNRS-Universite d’Orleans, Orléans, France
A 2D transient heat conduction model was created in COMSOL Multiphysics to simulate temperature changes in material irradiated by a KrF laser beam confined on silicon’s surface. In this paper, the obtained results are shown and discussed in case of bulk Silicon. The heat source is distributed in time with ‘gate’ and ‘gaussian’ shapes. The thermal properties values ...
H. Lorenzen, J. Timmerberg, and S. Mylvaganam
Department of Electrical Engineering, UAS OOW, Wilhelmshaven, Germany
Department Technology/Engineering, Telemark University College, Porsgrunn, Norway
Efforts involving simulation of transmission line networks necessitate the accurate values of the parameters of the lines. In this paper, as an attempt in estimating such parameters, the parameters of high voltage asymmetric power lines are calculated. In the process of estimation, the three phase equivalent circuit model is used. The resistance and inductance of such lines are dependent ...
T. Bjornara, and E. Aker
NGI, Oslo, Norway
Various types of equation system formulations for modeling two-phase flow in porous media using the finite element method have been investigated. These allow for equation manipulation such that the main differences between the formulations are the dependent variables that are solved for. Here we have tested five different formulations for 2D simulations and one for 1D; the Buckley-Leverett ...
Dinex Emission Technology A/S, Middelfart, Denmark
Exhaust noise must meet legislation targets, customer expectations and cost reduction which call for design optimization of the exhaust systems in the design phase. One solution is to use 3 dimensional linear pressure acoustics and calculate the transfer matrix of the muffler. The transfer matrix is the basis for calculating either the insertion loss or transmission loss of a muffler. The 3D ...
M. Zampolli, N. Malm, and A. Tesei
NURC NATO Research Centre, La Spezia, Italy
COMSOL AB, Stockholm, Sweden
Perfectly matched layers (PML) are an efficient alternative for emulating the Sommerfeld radiation condition in the numerical solution of wave radiation and scattering problems. The key ingredient of the PML formulation is the complex scaling function, which controls the anisotropic damping of the PML. The objective of this study is to propose a modified complex scaling function capable of ...
E. Holzbecher, and Hang Si
Weierstrass Institute for Applied Analysis and Stochastics (WIAS), Berlin, Germany
In the paper we examine the accuracy of various meshes for different model regions and simple differential equations in 2D and in 3D. We study the potential equation for a single irregular domain (2D testcase 1), for a simple domain with irregular sub-domains (2D testcase 2) and a 3D testcase. For testcase 1 we compare with the analytical solution, for testcases 2 with the best solution, ...
H. Conrad, T. Klose, T. Sandner, D. Jung, H. Schenk, and H. Lakner[1,2]
Semiconductor and Microsystems Technology Laboratory, Technische Universität Dresden, Germany
Fraunhofer Institute for Photonic Microsystems Dresden, Germany
Within this paper the so called “birth and death” method is demonstrated in use with COMSOL Multiphysics®. With this method the free and reactionless movement of a solid structure on deformed geometries and the activation of this solid structure at later simulation steps is possible. For demonstrating the benefit, this method was applied to simulate the thermal induced ...