Non-Newtonian Fluids: The Pouring Ketchup Quandary
Jennifer Segui | April 11, 2013
If you enjoy ketchup with your food, there’s a good chance you’ve experienced what we’ll call here the all-or-nothing ketchup quandary. You know, that moment when you reach for a new glass bottle of ketchup, remove the cap, and turn the bottle practically upside down — and then nothing happens. Intuitively you shake or tap the bottle, and then suddenly your food is completely coated in ketchup (unless your reflexes are really good, of course). In this blog post we explain the all-or-nothing effect of pouring ketchup, with a simulation of “ketchup flow from a bottle”.
Where Is My Ketchup?
Ketchup, in addition to being an exceptionally popular condiment, is also a non-Newtonian fluid. This is the key to its curious behavior. As a non-Newtonian fluid, ketchup’s viscosity — and consequently its ability to flow — varies with the velocity gradient across the fluid or the shear rate. When you first turn the ketchup bottle upside down, it’s probable that you will get only very minimal flow, if any at all, due to its high initial viscosity. Fortunately, ketchup also has an interesting shear thinning property. When an external force is applied in addition to gravity, the increased shear will result in decreasing the ketchup’s viscosity, allowing the product to flow more readily. This is why we sometimes must tap or shake the bottle to enjoy ketchup with our fries.
Simulating a Non-Newtonian Fluid Flow from a Bottle
To satisfy our curiosity, as well as our appetites, and come one step closer to perfecting our ketchup-pouring technique, we have simulated ketchup flow from a bottle using COMSOL Multiphysics and the CFD Module. In this simulation, we have made a few simplifying assumptions, including the infinite extent of the bottle (our ketchup lasts forever!), and single phase laminar flow, thereby ignoring air trapped in the bottle. All velocities presented are in meters per second (m/s).
We specified the geometry of our bottle and boundaries for laminar flow including a no-slip wall, pressure inlet (representing the weight of the portion of ketchup not modeled), and pressure outlet (the external atmosphere) as demonstrated in the figure below.
2D geometry used for the simulation. Applied boundary conditions are shown.
We also added the volume force feature to include gravity and the force resulting from shaking the bottle along the y-axis for 0.2 seconds.
In order to provide the solver with consistent initial conditions, volume force due to gravity is ramped up from 0 to its full magnitude with a step function (the transition zone is 0.05 seconds wide). The shaking action is simulated with a 0.2 seconds wide rectangle function, during this interval volume forces are doubled.
We ran the simulation for a preparation of ketchup based on data available by Koocheki et al. To simulate ketchup flow, we used the non-Newtonian power law to express the dynamic viscosity. The ketchup formulation was simulated by specifying the consistency coefficient and the flow behavior index in the power law equation. The following set of images demonstrates the higher initial viscosity and non-Newtonian flow in a ketchup formulation with 1% added Xanthan gum.
Viscosity measured in p1 (see Model Set-up above) as a function of time, time interval [0,0.1] seconds.
Viscosity measured in p1 (see Model Set-up above) as a function of time, time interval [0.1,2] seconds. Shear thinning properties of ketchup are evident especially during the [1,1.2] seconds interval when the bottle is shaken, viscosity decreases thus allowing more product to flow out of the bottle.
The All-or-Nothing Ketchup Quandary
Waiting for a change in the flow rate may seem familiar to you. Once the flow rate does start to change, it changes very quickly resulting in a ketchup deluge that quickly coats our food. The intrinsic increase in flow velocity results in an increasing shear that in turn lowers the viscosity leading to an even higher flow velocity. This is why ketchup seems to be initially stationary but then suddenly flows like water.
The particular subject of ketchup flow from a bottle is more complex than it may seem at first. There are many variables that impact how quickly we experience an all-or-nothing ketchup surprise. If you’re interested in investigating this effect further, I encourage you to experiment with COMSOL Multiphysics and the CFD Module. You could, for instance, study the effect variables such as tilt angle, air trapped in the bottle, and even bottle design, have on the ketchup pouring experience.
The Graphene Revolution: Part 3
- Applications 29
- Certified Consultants 32
- Chemical 67
- COMSOL Now 150
- Conference 116
- Core Functionality 106
- Electrical 176
- Fluid 117
- Interfacing 44
- Mechanical 209
- Multipurpose 21
- Tips & Tricks 14
- Trending Topics 62
- User Perspectives 96
- Video 72